
IM 01C21B01-01E
8-5
8. BRAIN TERMINAL BT200 OPERATION
T0806.EPS
Auxiliary setting data 1D Menu nameAUX SET 1
—
NORMAL/REVERSE
NORMAL/REVERSE*
4
Output reversalD40 REV OUTPUT
Impulse piping
accessing direction
D45 H/L SWAP
—
HIGH/LOW, –5 to 110%*
3
CPU errorD52 BURN OUT
Selected from mmH
2
O, mmAq,
mmWG, mmHg, Torr, Pa, hPa, kPa,
MPa, mbar, bar, gf/cm
2
, kgf/cm
2
,
inH
2
O, inHg, ftH
2
O, psi, or atm
Static pressure setting
units
D31 STAT. P. UNIT
Hardware errorD53
Same as A60
HOLD/HIGH/LOW, –5 to 110%*
3
ERROR OUT
Self-diagnostic
messages
—
D60 SELF CHECK
Auxiliary setting data 2E
OFF/ON
Menu nameAUX SET 2
Bidirectional modeE30 BI DIRE
MODE
Same as A60Self-diagnostic
messages
E60 SELF CHECK
—
—
No. Description RemarksItem
Menu nameAutomatic setupHAUTO SET
—
Adjustment dataJ
–5 to 110.0%*
3
Menu nameADJUST
Automatic zero
adjustment
J10 ZERO ADJ
—
—
—
—
—
—
—
—
—
Manual zero
adjustment
J11 ZERO DEV.
ENABLE/INHIBITExternal zero-
adjustment screw
permission
J20 EXT. ZERO
ADJ
Same as A60Self-diagnostic
messages
J60 SELF CHECK
Display the error
History of the errorsRECORD
Last errorP10
P11
ERROR REC 1
Display the errorOne time beforeERROR REC 2
P12 Display the errorTwo time beforeERROR REC 3
Menu nameTes tsK TEST
–5 to 110.0%*
3
Displays ‘ACTIVE’
while executing
Test output % settingK10 OUTPUT in %
Same as A60Self-diagnostic
messages
K60 SELF CHECK
Menu nameMemoM
P
MEMO
8 uppercase alphanumericsMemoM10 MEMO 1
8 uppercase alphanumericsMemoM20 MEMO 2
8 uppercase alphanumerics
P13 Display the errorThree time beforeERROR REC 4
P60 Same as A60Self-diagnostic
messages
SELF CHECK
MemoM30 MEMO 3
8 uppercase alphanumericsMemoM40 MEMO 4
8 uppercase alphanumericsMemoM50 MEMO 5
Same as A60Self-diagnostic
messages
M60 SELF CHECK
–32000 to 32000Automatic measure-
ment range lower
range value setup
H10 AUTO LRV
–32000 to 32000Automatic
measurement range
higher range value
setup
H11 AUTO HRV
—
—
—
—
—
–10.00 to 10.00% 0.00%
0.00%
Manual span adjustment
J15 SPAN ADJ
–10.00 to 10.00%4mA adjustmentJ30 OUTPUT 4mA
0.00%–10.00 to 10.00%20mA adjustmentJ31 OUTPUT
20mA
Same as A60Self-diagnostic
messages
H60 SELF CHECK
Applica-
bility
PLF
As specified when ordered.
If not specified, MPa.
If not specified, NORMAL.
NORMAL
HIGH
HIGH
OFF
OFF/ONAuto-recover from
sensor error
E50 AUTO
RECOVER
ON
OFF/ON*
5
DFS modeE10 DFS MODE
—
ON
AMP. TEMP/CAP. TEMP*
5
Reference temperature
sensor
E14 TEMP
SELECT
—
CAP. TEMP
10.00*
5
Zero shift
conpensation setup
E15 TEMP ZERO
—
0.00
Displays the same data as
C21.
Displays the same data as
C22.
Rewrita-
bility
Default Value
*1: In case of Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is not a measured value.
*2: When Optional code /F1 is specified, substitute the value with 0.1.
*3: When Optional code /F1 is specified, substitute the value –5 with –2.5.
*4: Not applicable for Model EJA115.
*5: Applicable only for Model EJA118W, EJA118N, EJA118Y, EJA438W, and EJA438N.
*6: See MWP(max. working pressure) on the nameplate. B40 shows an approximate value of maximum pressure for the capsule.
Comentários a estes Manuais