Yokogawa ADMAG AXR Manual do Utilizador Página 120
- Página / 194
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
<9. OPERATION VIA HART CONFIGURATION TOOL (HART 7)>
9-1
IM 01E30D01-01EN
9.
OPERATION VIA HART CONFIGURATION TOOL (HART 7)
ThisChapterdescribesthedevice(AXR)operation
proceduresusingaHARTcongurationTool(such
as FieldMate).
NOTE
For more details regarding the operations for
theHARTcongurationtool,refertotheHART
congurationtooloperationsmanual.
Note: HART is a registered trademark of the HART
Communication Foundation.
9.1 HART Protocol Revision
For the models with the output signal code “-J”,
HART protocol revision 5 or 7 is selectable. The
protocolrevisionissetasspeciedintheorder.
Howtoconrmprotocolrevisionisshownbelow.
Therearetwowaystoconrmtheprotocolrevision
set to the transmitter.
(1)Conrmationbythenameplate
The HART protocol revision at the time of
shipment is shown by the last number at the
serial number column of the name plate.
42
F0901.ai
XXX…XX
5: HART 5
7: HART 7
(2) ConrmationbyusingHARTcongurationtool
Follow the procedure below.
1)Connectthecongurationtooltothedevice.
2) Call up “Review4” display.
[Root Menu]→Review→Review4
3) HART protocol revision is displayed on the
“Universal rev” column.
IMPORTANT
Protocol revision supported by HART
congurationtoolmustbethesameorhigher
than that of the device.
Protcol revision
supported by HART
c
ongurationtool
5 7
Protocol revision of
the device
5
7 ×
:
Communication OK
×: Communication NG
NOTE
• In this User’s Manual, HART protocol
revision 5 and 7 are described as HART 5
and HART 7 respectively.
• HART 7 communication is supported by
FieldMate R2.04 or later.
NOTE
When the output signal code of the device is “-J”,
HART protocol revision can be changed. Refer
to subsection 9.8.5 about the procedure of the
revision change of HART 5 and HART 7.
9.2 Device Description (DD) on
aHARTCongurationTool
and AXR Device Revision
9.2.1 DD Revision and Device Revision
BeforeusingtheHARTCongurationTool(such
asFieldMate),conrmthattheDD(Device
Description)oftheAXRisinstalledinthe
CongurationToolbeforeusing.
• AXR:HART7
• Device type: 0x3757
• Device Revision: 10
• DD Revision: 1
TheDDrevisionsforAXRandCongurationTool’s
canconrminaccordancewiththefollowingsteps.
If the correct DD is not installed in the HART
- IM 01E30D01-01EN 1
- Contents 2
- EQUIPMENT 6
- 1. INTRODUCTION 7
- 1.1 Using the Magnetic 8
- Flowmeter Safely 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. HANDLING PRECAUTIONS 11
- 2.4 Installation Location 12
- Precautions 12
- 3. INSTALLATION 13
- 3.2.1 General Precautions 15
- 40 mm (1.5 in.), Wafer Type 17
- <3. INSTALLATION> 18
- 4. WIRING 25
- Waterproof gland 26
- Drain valve 27
- F0406.ai 27
- 4.4 Grounding Connection 28
- 4.5 Wiring Connections 29
- 4.6 Wiring Procedure 30
- <4. WIRING> 32
- Magnetic 34
- Recorder 35
- AXR Terminal 36
- Distributor, etc 37
- (5) Installing the Cover 39
- (USING THE DISPLAY UNIT) 40
- F0501.EPS 41
- 5.1 Operating Panel 41
- CongurationandFunctions 41
- SETESC INC 42
- DEC/SHIFT 42
- P:Protect 43
- B:Easy Setup 43
- C:Basic Setup 43
- 5.2.2 Setting Mode 44
- F0504-2.EPS 45
- F0505-2.ai 47
- F0506-1.ai 47
- F0506-2.ai 48
- 6. PARAMETER DESCRIPTION 49
- 6.3 Parameter List Overview 50
- 6.4 Parameter Description 64
- Setting Function 67
- No Execution No execution 67
- Meter factors 68
- Upper 2 digits 71
- Lower 6 digits 71
- Ranges Switching 74
- 5.6mA(10%) 80
- 18.4mA(90%) 81
- Default setting (Enable) 88
- Write protection (Protect) 88
- Default setting 88
- After password setting 88
- 6.5 Alarm Functions 89
- 6.5.4 NE-107 status 94
- 7.1 BT200 Basic Operations 95
- ( B ) ( y )( o ) 96
- ( m )( I ) 96
- 7.2.1 BT200 Connection 97
- ( ) key 98
- ( ) 98
- “FI-1101” to “FI-1201.” 102
- XXX…XX 103
- 5: HART 5 103
- 7: HART 7 103
- Distributor 104
- 8.6 Data Renewing 105
- 8.4 Basic Setup 105
- 8.5 ParametersConguration 105
- 8.8 HARTSpecicFunctions 106
- 8.8.2 Fixed Current Output 107
- 8.8.3 Burst Mode 107
- 8.8.4 Multidrop Mode 107
- (continued on next page) 110
- IMPORTANT 121
- Device Information 122
- 9.8 HARTSpecicFunctions 123
- 9.8.2 Trim Analog Output 124
- 9.8.3 Burst Mode 125
- 9.8.3.2EventNotication 128
- 9.8.4 Multidrop Mode 129
- F0910.ai 135
- 10. ACTUAL OPERATION 138
- 21:Adjustment 20mA 139
- M:Adjustment 140
- 10:Auto Zero Exe 140
- 11:Autozero Time 140
- Now Auto Zero 140
- Executing 140
- 11. MAINTENANCE 141
- 11.2 Components Replacement 142
- <11. MAINTENANCE> 143
- 11.3 Setting of Switches 145
- 11.4 Adhesion diagnostic 146
- Dielectric Strength Test 149
- 11.7 Troubleshooting 150
- 11.7.2 Unstable Zero 151
- 12. OUTLINE 153
- Alarms and Setting Alarms 155
- Flowtubes 156
- HAZARDOUS AREA CLASSIFICATION 157
- Spaninm/s(ft/s) 158
- 25 to 50 mm (1.0 to 2.0 in.) 160
- (flange type, wafer type) 160
- 65 to 200 mm (2.5 to 8.0 in.) 160
- <12. OUTLINE> 161
- Electrical 167
- Connection 167
- Indicator 167
- Electrical Connection 167
- Unit: mm (approx. inch) 171
- General-purpose Use; 176
- Explosion Proof Type; 176
- INSTRUMENT 178
- Terminals 179
- 14.2 FM 180
- 14.3 IECEx 181
- 14.4 TIIS 183
- Digital output circuit 185
- Supply/ Output signal circuit 185
- Installation 186
- A1.2.7 Startup Time 187
- A1.2.8 Firmware Update 187
- A1.2.9 Reliability Data 187
- A1.3 Denitionsand 188
- Abbreviations 188
- A1.3.2 Abbreviations 189
- FOR TIIS FLAMEPROOF EQUIPMENT 190
- Apparatus 191
- 5. External Wiring for 191
- Flameproof Apparatus 191
- 7. Selection of Cable Entry 193
- Devices for Flameproof Type 193
- Revision Information 194
Manuais e produtos relacionados com Sensores Yokogawa ADMAG AXR
Sensores Yokogawa AXFA14G/C Manual do Utilizador
(76 páginas)
(76 páginas)
Sensores Yokogawa ADMAG AXF Manual do Utilizador
(112 páginas)
(112 páginas)
Sensores Yokogawa ADMAG AXF Manual do Utilizador
(133 páginas)
(133 páginas)
Sensores Yokogawa AXFA14G/C Manual do Utilizador
(18 páginas)
(18 páginas)
Sensores Yokogawa AXFA14G/C Manual do Utilizador
(123 páginas)
(123 páginas)
Sensores Yokogawa ADMAG AXF Manual do Utilizador
(107 páginas)
(107 páginas)
Sensores Yokogawa RAGL Manual do Utilizador
(2 páginas)
(2 páginas)
Sensores Yokogawa RAGN Manual do Utilizador
(46 páginas)
(46 páginas)
Sensores Yokogawa RAKD Manual do Utilizador
(72 páginas)
(72 páginas)
Sensores Yokogawa RAMC Manual do Utilizador
(136 páginas)
(136 páginas)
Baumer Sensors user manuals
Starting on O
Comentários a estes Manuais