Yokogawa PC-Based MX100 Manual do Utilizador

OperationGuideMX100Data Acquisition UnitIM MX100-02E5th Edition

10IM MX100-02EFlow of Operation during InstallationThe figure below shows the general flow of operation when the MX100 is installed initially.Wire the

11IM MX100-02EFunction of the ModulesMain ModuleThe main module is equipped with a power supply connector, a power switch, an Ethernet port, a CF card

12IM MX100-02E• 6-CH, Medium-Speed 4-Wire RTD Resistance Input Module (MX110-V4R-M06) • Minimum measurement interval: 100 ms• Maximum number of i

13IM MX100-02E• 8-CH, Medium-Speed Analog Output Module (MX120-VAO-M08) • Output update interval: 100 ms (shortest)• Maximum number of outputs: 8

14IM MX100-02EFunctions of the MX100 Standard SoftwareThe MX100 Standard Software consists of the three software programs below.Integration MonitorEna

15IM MX100-02ESignal Wiring of the MX100For a description of the installation procedure, module attachment procedure, signal wiring details, and wirin

16IM MX100-02EWiring the Universal Input Module and DCV/TC/DI Input Module • Thermocouple input • RTD inputLead wire resistance per wire of 10 Ω or

17IM MX100-02EWiring the Strain Input Modules• One-Gauge Method Setting switchONOFFNo.1No.2No.3No.4No.5A(+V)B( L) C(-V)D( H) -B12, -B35EeRgRRRRgNo.1O

18IM MX100-02E• Adjacent Two-Gauge Method ONOFFNo.1No.2No.3No.4No.5A(+V)B(L)C(-V)D( H) No.1ONNo.2ONNo.3OFFNo.4OFFNo.5ONRg1Rg2RREeRg1Rg2Rg1Rg2Setting

19IM MX100-02E• Opposing Two-Gauge Three-Wire Method RRRg2Rg1EeRg1Rg2Cannot be connected. Use -NDI.rrrrrr-B12, -B35 R: fixed resistancer: resis

2IM MX100-02EUser RegistrationThank you for purchasing YOKOGAWA products.We invite you to register your products in order to receive the most up to da

20IM MX100-02E• Four-Gauge Method ONOFFNo.1No.2No.3No.4No.5A(+V)B( L) C(-V)D( H) -B12, -B35No.1OFFNo.2OFFNo.3OFFNo.4OFFNo.5ONRg1Rg2Rg4Rg1Rg2Rg3Ee

21IM MX100-02EWiring the Digital Input Modules (-D05, -D24)Note• On the digital input modules, the negative terminals and empty terminals of all chan

22IM MX100-02EWiring the Analog Output Modules External power supply VoltageV+Load+24 Vpower supply(when using current output)Direction ofcurrentVex

23IM MX100-02EWiring the Digital Output Module CNO250 VDC/0.1 A, 250 VAC/2 A, or30 VDC/2 A (resistance load)Main Output SpecificationsContact mode:

24IM MX100-02EConnection to the NetworkConnecting the Ethernet Cable to the Main ModuleConnect the Ethernet cable to the Ethernet port (10BASE-T/100BA

25IM MX100-02ESetup Procedures of the MX100 Standard SoftwareFor details on the setup procedure, see the MX100 Standard Software User’s Manual (IM MX1

26IM MX100-02EOperations of the MX100 Standard SoftwareConnecting to or Disconnecting from the MX100Before carrying out the following procedure, check

27IM MX100-02E4. Click the icon indicating the MX100.The network information about the MX100 appears. Click the iconNetwork information5. Clic

28IM MX100-02E7. Click the icon indicating the MX100 again. The network information about the connected MX100 appears again.8. Click Connect.

29IM MX100-02E2. Click Disconnect. Click Disconnect.Reconnecting to the Same MX100• If the Connection screen is opened, click Connect. Cli

3IM MX100-02EContentsChecking the Contents of the Package ...

30IM MX100-02ESetting the Acquisition Conditions of the Measured DataClick Acquisition on the Monitor bar. Set the conditions on the Acquisition setup

31IM MX100-02E• Monitor interval setup example As shown in the figure below, the waveform display area is shown for each monitor interval.Setting th

32IM MX100-02ESetting Measurement ConditionsClick Channel on the Monitor bar to display the Channel setup screen. Click the Meas. Channel tab.Set the

33IM MX100-02E Set the initial balance for strain input channels (only when the input mode is set to STR)Channel NumbersSee “Attachment Position and

34IM MX100-02ESetting the Measurement SpanSet the minimum and maximum values of the range that is actually measured within the measurable range.Settin

35IM MX100-02EMonitoring the Measured Data and Setting the DisplayClick Monitor on the Monitor bar. You can monitor the measured data on the Monitor s

36IM MX100-02EMonitoring the Data Using Trend Waveforms and Numeric ValuesNumeric display screen Waveform display screenSwitch the display groupChange

37IM MX100-02EChanging the Display ConditionsClick Display on the Monitor bar. You can change the display conditions on the Display setup screen that

38IM MX100-02ESelecting the Display Zone of the Trend WaveformYou can select from the following. Taking the bottom and top edges of the waveform displ

39IM MX100-02E• Auto zone Displays the trend waveforms by dividing the waveform display area evenly according to the number of displayed waveforms r

4IM MX100-02EThank you for purchasing the MX100 Data Acquisition Unit.This manual concisely describes the handling procedures of the MX100 Data Acquis

40IM MX100-02EDisplaying MarksYou can display marks in the trend waveform area (see the figure below). You can enter a text to be attached to the mark

41IM MX100-02ETo clear the cursors, choose Hide Cursor from the View menu. ChooseRecording the Measured DataFor details on setting of the record sta

42IM MX100-02ESetting AlarmsClick Channel on the Monitor bar to display the Channel setup screen. Enter settings in the Meas. Channel or Math Channel

43IM MX100-02EAlarm TypeThe following six alarm types are available.When not using differential input on measurement channels, select OFF, High, or Lo

44IM MX100-02EAlarm HysteresisYou can set a width (hysteresis) to the values used to activate and release alarms. Alarm hysteresis prevents frequent a

45IM MX100-02EEnergized/De-energized Operation of Output RelaysYou can select whether the output relay is energized or de-energized when an output eve

46IM MX100-02ESetting the ComputationYou can enter computing equations using operators, constants, and functions. The computed results be displayed an

47IM MX100-02ELoading Setup Data (Project)From the File menu, choose Open. Printing Setup DataFrom the File menu, choose Print. Settings such as the

48IM MX100-02EDisplaying Recorded Measured Data, Reading Values Using Cursors, and Statistical Computation over an AreaYou can display measured or com

49IM MX100-02EChanging the Display on the Waveform Display WindowYou can change the display using operations similar to the waveform display area of t

5IM MX100-02EChecking the Contents of the PackageUnpack the box and check the contents before operating the instrument. If some of the contents are no

50IM MX100-02EOperations of the MX100 Standard SoftwareChanging the Display Using the Display Setup WindowSee the explanation in the figure below. Cha

51IM MX100-02EReading Values Using CursorsClick the tab of the group on which you wish to read values using cursors on the waveform display window. Cl

52IM MX100-02EAlarm/Mark List Display Displays a detailed list of alarms and marks.From the Window menu, choose Alarm/Mark List.You can also click the

53IM MX100-02EPrinting the Displayed DataTo print waveforms, open the waveform display window; to print numeric values, open the numeric display windo

6IM MX100-02EUniversal Input Module, DCV/TC/DI Input Module, and Four-Wire RTD Resistance Input ModuleModel Suffix Code DescriptionMX110Input type -UN

7IM MX100-02EStandard AccessoriesThe following standard accessories are supplied with the main module. Check that all contents are present and that th

8IM MX100-02E 2, 31 54 6 78 9 1110 12 13 14Shunt ResistorsNo. Name Model Min. Q’ty Note15 Shunt resistor (for the clamp terminal)438920 1 Resistanc

9IM MX100-02EFunction IntroductionFor further details on each function, see the MX100 Data Acquisition Unit User’s Manual (IM MX100-01E) and the MX100