Yokogawa DAQWORX Manual do Utilizador Página 22
- Página / 210
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
1-14
IM WX102-01E
• RL: Rate-of-change lower limit alarm
Triggers an alarm when negative change of measured value exceeds the specied
value within the specied interval.
• DH: Delta high limit alarm
This alarm is applicable only for channels for which Delta is selected. Triggers an
alarm when the difference of measured values between two channels exceeds the
specied value.
• DL: Delta low limit alarm
This alarm is applicable only for channels for which Delta is selected. Triggers an
alarm when the difference of measured values between two channels drops below the
specied value.
Measured
value
Rate-of-change
upper limit alarm
T
Time
Specified interval
1
T
2
t
1
t
2
Change of
measured value
2 1
T
Time
2
T
1
t
1
t
2
Measured
value
Rate-of-change
lower limit alarm
T –T
Change of
measured value
21
T –T
Specified interval
t –t
2 1
t –t
2 1
Note
• Alarm settings will be cleared in the following cases.
The measurement mode/input type (VOLT, TC, ...) is changed.
The measurement range is changed.
The span or scaling value is changed (including change of the decimal point position) during
scale conversion display mode.
Channel No., input type or input range of the standard channel is changed during delta
measurement mode.
• For pulse input channels and power monitor channels, “RH:rate-of-change upper limit alarm”
/ “RL: rate-of-change lower limit alarm” are not available.
Alarm hysteresis
A specified margin (hysteresis) can be added to the specified alarm level. (Common to all
alarms).
Alarm point (level)
Alarm OFF
Measured value
Alarm ON
1V
Hysteresis (approx. 0.5%)
Upper alarm limit (H)
1V
Lower alarm limit (L)
Measured value
Alarm OFF
Hysteresis (approx. 0.5%)
Alarm point (level)
Alarm ON
1.5 DA100 Functions
- DAQ 32 Plus 1
- DAQ 32 Plus Client Package 1
- Trademarks 2
- Revisions 2
- Software License Agreement 3
- How to Use this Manual 5
- Contents 6
- Chapter 5 Logger Software 7
- Introduction 9
- 3 Logger 10
- 4 Historical Viewer 10
- 5 Tag Editor 10
- 1.2 Required PC Environment 12
- Communication board 13
- Opening DAQ 32 Plus Software 15
- Closing DAQ 32 Plus software 16
- 1.5 DA100 Functions 17
- Setting the measurement range 18
- Before Operation 19
- Input Related Functions 20
- Alarm setting 21
- • DH: Delta high limit alarm 22
- • DL: Delta low limit alarm 22
- Alarm hysteresis 22
- Alarm output relay AND/OR 23
- Reflash alarm 24
- Non-hold mode: 24
- Hold mode: 24
- Event mode 25
- Basic operators 26
- Logical operators 27
- Relational operators 27
- Special operators 28
- Math for PULSE input module 28
- Math operation control 30
- Output Formats 30
- Report Time 31
- Report Channels 31
- Computing Types 31
- Sum and Cumulative Sum 31
- Unit of Summation (SUM UNIT) 32
- Start/Stop Reporting 32
- Output Report 32
- 2.1 Launcher Software 34
- 2.2 Making Project Settings 35
- Switching Projects 37
- Protecting Projects 37
- Menu button 38
- Launcher icon 38
- Help button 38
- Setting Screen 39
- Setting Order 39
- ETHERNET I/F 40
- 10BASE-T 40
- 3.3 Communication Settings 42
- System Reconstruction 44
- System Scan 45
- System Initialization 46
- Display Errors 46
- Confirming the ROM Version 47
- Base Setting Data 48
- Selecting Setting Screen 49
- System Configurations 49
- 4.2 Loading Setting Data 50
- Setting the Wiring Method 53
- Setting the Input Range 53
- Setting the Span 54
- DARWIN Hardware Configurator 56
- Setting the Span (SPAN) 57
- 4.4 Alarm Settings 58
- Setting alarm values 59
- RH and RL 59
- Moving Average Settings 61
- Filter Settings 61
- Setting Procedure 62
- Interpolation (INTERPOL) 63
- DR with FDD Option Only) 65
- Tag setting 66
- Computation equation 71
- Restrictions in equations 71
- Copy button Paste button 72
- Items to copy 72
- Click to select all items 72
- 4.13 Setting Constants 74
- Selecting Events 76
- Selecting Actions 77
- Groups Setting 79
- Setting Timers 80
- Summer/Winter Time 81
- Recording Mode Settings 82
- Chart Speed Settings 83
- Entering a Header 83
- Entering a Title 83
- Setting the List Format 83
- Message tab 84
- Use of Trigger (WRITE TRIG) 85
- 6 1 0 1 0 0 0 0 . D A T 86
- F I L E – 0 0 1 . D A T 86
- Pretrigger (WRITE PRETRIG) 87
- Data Format 87
- Data Capacity 87
- Scan Interval 88
- File of Retransmission Output 89
- Display Hold 90
- Reflashing Alarm Setting 91
- Relay AND/OR 91
- Relay (De-)Energizing 91
- Relay Hold Setting 91
- Recording Colors 92
- 4.23 Report Settings 93
- Math Setup 95
- (for DC100, and DR only) 97
- Channel number or Tag display 98
- Dot-printing Recording System 98
- IM WX102-01E 100
- Copy-lock to floppydisk 101
- Copy-lock password 101
- Display Update Interval 102
- Indication for Display 102
- Key Lock 102
- 4.29 System Configuration 103
- Adding and removing subunits 104
- Adding and Removing Modules 104
- 4.31 Initializing Settings 105
- 4.32 Sending Setting Data 106
- 4.33 Saving Setting Data 107
- Statusbar 108
- 4.35 Printing Settings 109
- Starting Logger software 111
- 5.2 Logging Configuration 112
- 5.3 Group Settings 115
- Color display 119
- Meter display 119
- Digital value display 120
- Alarm display 120
- Displaying groups 120
- Setting alarm noise ON/OFF 120
- Pause button 121
- Monitor/Record stop button 121
- 5.6 Changing Monitor Display 122
- Y-axis display area 123
- Zone display bars 123
- Linking other monitors 124
- Alarm Settings 125
- 5.7 Cursor Measurement 126
- Start Recording 127
- Stop Recording 127
- ‘Communication’ icon 128
- ‘Acquisition’ icon 128
- ‘Math’ icon 128
- ‘Report condition’ icons 128
- Saving Files 129
- Loading Files 129
- Starting/Stopping Reports 130
- Waveforms 132
- 5.14 Using the DDE Server 133
- Operating Procedure 134
- Quitting the Auto Processor 135
- Waveform display 137
- Digital value sheet 138
- Viewing file info 140
- 6.3 General Display Settings 141
- • User Zone 144
- • Edit Zone 144
- • Full Zone 144
- • Slide Zone 144
- • Auto Zone 145
- • Multi-Axis Zone 145
- 6.6 Cursor Measurement 147
- Searching for alarms 149
- Searching for marks 149
- 6.9 Notepad Copying 151
- 6.10 Displaying Alarm Info 152
- User Defined mark 154
- User defined mark 154
- Trigger mark 154
- Deleting Marks 155
- Resetting Marks 155
- Converted File Formats 159
- 6.15 File Formats 160
- Acquisition time, last data 161
- Sample rate 161
- Data count 161
- Channel number 162
- Tag Comment 162
- Date format 163
- Measurement time, and period 164
- Vertical channel format 168
- Horizontal channel format 168
- Starting the tag editor 170
- Displayed information 170
- 7.2 Receiving Tag Data 171
- Paste button 172
- Copy button 172
- Calibration procedures 174
- 8.2 Auto Calibration 175
- Auto tab 176
- Message confirming 176
- Input voltage 176
- 8.3 Manual Calibration 177
- Explanation 178
- (DA, DC only) 179
- 8.5 Saving Calibration Data 182
- Starting the Remote Monitor 183
- Functions 183
- Status bar display 184
- Setting the Tome Axis 185
- Alarm Display Placement 185
- Conditions 186
- Saving connection conditions 187
- Monitor/Using Cursors 188
- Cursor operation 189
- Pausing Monitor Display 190
- Closing Monitor Display 190
- Exiting Monitor Display 191
- Status bar 193
- Division Settings 202
- Output file names 202
- 11.1 Troubleshooting 203
- Warning Messages 204
- Error Messages <Common> 204
- Error Messages <Logger> 205
- Messages 207
Manuais e produtos relacionados com Software Yokogawa DAQWORX
Software Yokogawa DAQWORX Manual do Utilizador
(17 páginas)
(17 páginas)
Software Yokogawa DAQWORX Manual do Utilizador
(52 páginas)
(52 páginas)
Software Yokogawa DAQWORX Manual do Utilizador
(100 páginas)
(100 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.167 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais