Yokogawa DR240 Manual do Utilizador Página 40
- Página / 121
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
4-11
IM DR231-11E
Overview and Specifications of Ethernet Interface
4
The alarm status indicates two levels with one byte.
1 byte
Level2 Level1
Upper Byte
Lower Byte
1 byte
Level4 Level3
Upper Byte
Lower Byte
D1 to Dn, H1 to Hn: Alarm status (level 3, 4) (No output when p1 is 0)
Contents and format are the same as level 1 and 2.
E1 to En: Fixed to 80H
F1 to Fn: Computation channel number
The measured/computed data are output in the order specified by the
EB command.
Measured data
7FFFH (7FFF7FFFH): Positive over-limit data
8001H (80018001H): Negative over-limit data
8002H (80028002H): Measurement range setting skips.
8004H (80048004H): Abnormal data
8005H (80058005H): No data
*Data inside the parentheses ( ) are computed data.
EL Specifies the channel for outputting unit and decimal point informa-
tion and outputs it in ASCII format
Mode Operation mode
Syntax ELp1, p2<terminator>
p1 First channel to output (001 to 560, or A01 to A60)
p2 Last channel to output (001 to 560, or A01 to A60)
Description • A01 to A60 correspond to computation channels (A01 to A30 for the stand-alone
type).
• The data of expansion type channels that are not connected are not output.
• If there are no corresponding channels, E1 is returned.
• The unit and decimal information is not determined if measurement channels are
skipped or if abnormal data exist.
• The output format is as follows.
S1S2CCCUUUUUU, PCrLf
S1: Space (fixed)
S2: Data status
Space Intermediate data
E Last data
CCC: Channel number (3 characters)
001 to 560 or A01 to A60
UUUUUU: Unit(6 characters)
P: Decimal point position
0 00000
1 0000.0
2 000.00
3 00.000
4 0.0000
EB Specifies the byte order of output.
Mode Operation mode
Syntax EBp1<terminator>
p1 Byte order of output
0 MSB first (Default setting)
1 LSB first
Description • Sets the byte order of the binary data of the measured/computed data that are
output with the EF command.
• Since the DR determines the upper byte and lower byte in units of two bytes, four-
byte data are output as follows.
MSB first: ABCD
LSB first: BADC
4.7 Transferring the Instantaneous Values
- Communication Interface 1
- Instruction Manual 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 6
- CHAPTER 8 SAMPLE PROGRAM 6
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- Configuring from the PC 36
- 4.5 Connection Methods 37
- DR's IP address 42
- <Enter> 42
- 4.9 Setting the T imeout 43
- 5.1 Command Format 44
- 5.2 Command Syntax 46
- ●Stand alone model (DR130) 47
- 5.4 Command List 48
- Control Execution Command 49
- Output Request Command 49
- 5.4 Command List 49
- 5.5 Input Range Parameter 50
- RATE RATE 0 to 30000 52
- GATE GATE 0 to 30000 52
- 5.6 ASCII Code Table 54
- 6.1 Setting the Input 55
- Setting Scaling 56
- 6.1 Setting the Input 56
- SN Sets the scaling unit 57
- XQ Sets the filter 57
- 6.2 Setting Alarms 58
- 6.3 Setting the Display 59
- 6.4 Setting the Recording 60
- Commands 61
- Message setting 61
- Message copy 61
- XC Sets dot printing colors 63
- 6.5 Other Settings 64
- XB Sets the burnout 68
- 6.6 Control and Execution 71
- RS Reconstruct the system 74
- RC Initialize the set values 74
- 6.7 Data Output Request 75
- 7.1 Functions as Talker 77
- (ASCII code) 78
- (Binary code) 79
- Position 83
- ±DDDDDE-EpCrLf 87
- For Measured Data 90
- For Computed Data 90
- 7.13 Report Output Format 92
- Daily Report 94
- 7.13 Report Output Format 94
- Monthly Report 96
- 8.1 GP-IB Sample Programs 99
- IM DR231-11E 100
- 8.2 RS-232-C Sample Programs 102
- Output the Setting Data 105
- Sample Program 107
- 8.4 Ethernet Program 111
- 8.4 Ethernet Program 112
- App.1 Computing Equation 113
- Computation start 115
- Computation stop 115
- Computation clear & start 115
- Computed data 116
- Command Index 120
Manuais e produtos relacionados com Sensores Yokogawa DR240
Sensores Yokogawa µR20000 Manual do Utilizador
(263 páginas)
(263 páginas)
Sensores Yokogawa DR240 Manual do Utilizador
(293 páginas)
(293 páginas)
Sensores Yokogawa JUXTA VJCE Manual do Utilizador
(10 páginas)
(10 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais