Yokogawa DR240 Manual do Utilizador descarregar pdf (Página 61)

6-7

IM DR231-11E

Commands

SZ Sets the recording zone.

Mode Operation mode

Setting SZp1, p2, p3<terminator>

p1 Channel number (001 to 560)

Computation channel number (A01 to A60)

p2 Lower limit of zone (0 to 245 mm, or 0 to

145 mm for the DR130)

p3 Upper limit of zone (5 to 250 mm, or 5 to

150 mm for the DR130)

Example Set the recording zone of channel 6 in slot 3 of

subunit 4 to 10 to 50 mm.

SZ436, 10, 50

Comments • Set p2 smaller than p3.

• This is effective for analog recording.

• The optional computation channel number for a

stand-alone model is A01 to A30.

SP Sets partially expanded recording.

Mode Operation mode

Setting SZp1, p2, p3, p4<terminator>

p1 Channel number (001 to 560)

Computation channel number (A01 to A60)

p2 ON/OFF of partially expanded recording

ON Performs partially expanded

recording.

OFF Does not perform partially expanded

recording.

p3 Boundary recording position (1 to 99%)

p4 Boundary value

Example Partially compress and record channel 6 in slot 3 of

subunit 4 at the boundary recording position of 25%

for the boundary value 0 V.

SP436, 25, 0

Comments • A waveform can be partially expanded by setting

the set input level (boundary value) as a

percentage of the recording chart (boundary

recording position).

• This is effective for analog recording.

• If contiguous channels are set to p1, the decimal

point in boundary values when the measurement

ranges for set channels differ take the positions

determined for each measurement range (see

Pages 5-7 and 5-8). If the result exceeds the

measurable ranges, an error occurs. For example,

if the channels of measurement ranges 20 mV, 2

V, and type T thermocouple are set to p1 and the

boundary value is set to 10000, the following

applies:

• The boundary value for the channel of the 20

mV measurement range: 10.000 mV

• The boundary value for the channel of the 2 V

measurement range: 1.0000 V

• The boundary value for the channel of the type

T thermocouple: 1000.0°C

Since the measurement range of the type T

thermocouple is -200.0 to 400.0°C, an error

occurs. For decimal point positions, see Pages

5-7 and 5-8.

• The optional computation channel number for a

stand-alone model is A01 to A30.

• Set p4 to a value within the recording span, or

within the left/right scale if linear scaling is

applied. It is not possible, however, to set the

recording span nor the left/right scale.

• In the case of power monitor module, if the

settings of the wiring method and the input range

are changed, the partially expanded recording

setting is set to OFF.

SG Sets or copies a message.

Message setting

Mode Operation mode

Setting SGp1, p2<terminator>

p1 Message number (01 to 20)

p2 Message character string (Up to 16

characters)

Example Set the message “test” to message No. 5.

SG05, test

Comments • For details of the character strings that can be used

in messages, see the characters in the table of

ASCII codes on Page 5-11.

Message copy

Mode Operation mode

Setting SGp1, p2, p3<terminator>

p1 COPY

p2 Message number at a message source (01 to

20)

p3 Message number at a message destination

(01 to 20)

Example Copy message No. 5 to message No. 12.

SGCOPY, 05, 12

ST Sets a tag.

Mode Operation mode

Setting STp1, p2<terminator>

p1 Channel number (001 to 560)

Computation channel number (A01 to A60)

p2 Tag character string (up to 16 characters)

Example Set “TEST” as the tag for channel 6 in slot 3 of

subunit 4.

ST436, TEST

Comments • For details of the character strings that can be used

as tags, see the characters in the table of ASCII

codes on Page 5-11.

• The optional computation channel number for a

stand-alone model is A01 to A30.

SH Sets a header.

Mode Operation mode

Setting SHp1, p2<terminator>

p1 Setting line number (1 to 5)

p2 Header character string

Example Set the line of number 2 to “TEST RECORDE.”

SH2, TEST RECORDE

Comments • Set the character string to be printed in the first

place of a record.

• For details of the character strings that can be used

as headers, see the characters in the table of ASCII

codes on Page 5-11.

• Parameter p2 can have no more than 60 characters

for theDR130 and no more than 80 characters for

the DR230/240.

SJ Sets a title.

Mode Operation mode

Setting SJp1<terminator>

p1 Title character string (up to 32 characters)

Example Set the title to “TEST RECORDE.”

SJTEST RECORDE

Comments • Sets a character string which is recorded in a fixed

interval in analog recording. The interval to be

recorded is set using the XR command (see 6-9).

• For details of character strings that can be used as

titles, see the characters in the table of ASCII

codes on Page 5-11.

SF Sets the format for list printing.

Mode Operation mode

Setting SFp1, p2, p3, p4<terminator>

p1 ON/OFF of range list printing (ON, OFF)

p2 ON/OFF of alarm list printing (ON, OFF)

p3 ON/OFF of parameter list related to printing

(ON, OFF)

p4 ON/OFF of other parameters (ON, OFF)

6.4 Setting the Recording

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 120 121

Comentários a estes Manuais

Sem comentários

Yokogawa DR240 Manual do Utilizador Página 61

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Yokogawa DR240