Yokogawa DR240 Manual do Utilizador Página 47
- Página / 121
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5-4
IM DR231-11E
5.3 Setting a Channel No., and Alarm Output Relay
No.
Channel and relay numbers are expressed as shown below in three characters.
Unit No. + Slot No. + Number in slot
1
2 3
Channel/relay No.
Slot No. (In case of channel/relay No. 10, Slot No. + 1)
Unit No. ("A" for optional computation channel)
Channel Number
DR130/DR231/DR241 (Stand-alone type) DR232/DR242 (Expandable type)
Unit No. 0 0 to 5 (Subunit: DS400/DS600)
Slot No. 0 to2 (0 or 1 for DR130) 0 to 5
Channel No. 1 to 10 (CH10: 0)* 1 to 10 (CH10: 0)*
*: For CH10, the channel number digit is expressed by 0 and the slot number digit, by slot number + 1.
Note
• If successive channel numbers are to be specified, enter as ABC-DE, where
ABC: the above 3-digit channel number (unit no., slot no., and channel no.)
DE: the channel number except the unit number (slot no., and channel no.)
Successive channels can only be specified for a unit.
• The input module cannot be mounted to the DR232/DR242 main unit.
Relay Number
DR130/DR231/DR241 (Stand-alone type) DR232/DR242 (Expandable type)
Unit No. 0 I (DR232/DR242 main unit)*
1
S(Internal switch) S(Internal switch)
0 to 5 (Subunit: DS400/DS600)
Slot No. 1 to 5 (1 to 3 for DR130) 0 to 5
Relay No. 1 to 10 (Relay No. 10: 0)*
2
1 to 10 (Relay No. 10: 0)*
2
*1: If the recorder comprises any communication module, no alarm-output relay module can be mounted on
the recorder’s main unit. The unit number “I,” therefore, is not usable in setting up the recorder using
communication commands.
*2: For relay No. 10, the channel number digit is expressed by 0 and the slot number digit, by slot number + 1.
Example
• Channel 9 of the module mounted in slot 2 of the unit 3 of the extended model: 329
• Relay of No. 10 of the module mounted in slot 2 of the unit I of the extended model: I30
1
3
5
7
9
2
4
6
8
10
2
4
6
8
10
1
3
5
7
9
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
●Stand alone model (DR231/DR241)
●Module
●Stand alone model (DR130)
Slot 0
Slot 1
Slot 2
Slot 3
POWER
100-240V 50/60Hz 70VA MAX
STATUS
SUB UNIT
POWER
100-240V 50/60Hz 70VA MAX
STATUS
SUB UNIT
UnitI
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Unit No.
0 to 5*
1
(Sub-unit
DS400/DS600)
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
●Expandable model (DR232/DR242)
Unit No.
setting switch
*1 : The unit number of the sub-unit is the number
set by the switch located on each unit below
slot 2.
Make sure the settings comform the switch
setting.
- Communication Interface 1
- Instruction Manual 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 6
- CHAPTER 8 SAMPLE PROGRAM 6
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- Configuring from the PC 36
- 4.5 Connection Methods 37
- DR's IP address 42
- <Enter> 42
- 4.9 Setting the T imeout 43
- 5.1 Command Format 44
- 5.2 Command Syntax 46
- ●Stand alone model (DR130) 47
- 5.4 Command List 48
- Control Execution Command 49
- Output Request Command 49
- 5.4 Command List 49
- 5.5 Input Range Parameter 50
- RATE RATE 0 to 30000 52
- GATE GATE 0 to 30000 52
- 5.6 ASCII Code Table 54
- 6.1 Setting the Input 55
- Setting Scaling 56
- 6.1 Setting the Input 56
- SN Sets the scaling unit 57
- XQ Sets the filter 57
- 6.2 Setting Alarms 58
- 6.3 Setting the Display 59
- 6.4 Setting the Recording 60
- Commands 61
- Message setting 61
- Message copy 61
- XC Sets dot printing colors 63
- 6.5 Other Settings 64
- XB Sets the burnout 68
- 6.6 Control and Execution 71
- RS Reconstruct the system 74
- RC Initialize the set values 74
- 6.7 Data Output Request 75
- 7.1 Functions as Talker 77
- (ASCII code) 78
- (Binary code) 79
- Position 83
- ±DDDDDE-EpCrLf 87
- For Measured Data 90
- For Computed Data 90
- 7.13 Report Output Format 92
- Daily Report 94
- 7.13 Report Output Format 94
- Monthly Report 96
- 8.1 GP-IB Sample Programs 99
- IM DR231-11E 100
- 8.2 RS-232-C Sample Programs 102
- Output the Setting Data 105
- Sample Program 107
- 8.4 Ethernet Program 111
- 8.4 Ethernet Program 112
- App.1 Computing Equation 113
- Computation start 115
- Computation stop 115
- Computation clear & start 115
- Computed data 116
- Command Index 120
Manuais e produtos relacionados com Sensores Yokogawa DR240
Sensores Yokogawa µR20000 Manual do Utilizador
(263 páginas)
(263 páginas)
Sensores Yokogawa DR240 Manual do Utilizador
(293 páginas)
(293 páginas)
Sensores Yokogawa JUXTA VJCE Manual do Utilizador
(10 páginas)
(10 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais