Yokogawa DR240 Manual do Utilizador Página 70
- Página / 121
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
6-16
IM DR231-11E
For digital input module
60 mV, 6 V
Example Calibrate the 20-mV range on the module in slot 1 of
subunit 0.
XZ0, 1, CAL/EXEC, 20 mV
Correcting the calibration value manually
(universal module)
Setting XZp1, p2, p3, ..... , p25<terminator>
p1 Unit number (0 to 5)
p2 Slot number (0 to 5)
p3 DISPLAY
p4 Zero calibration value for 20-mV range
p5 Span calibration value for 20-mV range
p6 Zero calibration value for 60-mV range
p7 Span calibration value for 60-mV range
p8 Zero calibration value for 200-mV range
p9 Span calibration value for 200-mV range
p10 Zero calibration value for 2-V range
p11 Span calibration value for 2-V range
p12 Zero calibration value for 6-V range
p13 Span calibration value for 6-V range
p14 Zero calibration value for 20-V range
p15 Span calibration value for 20-V range
p16 Zero calibration value for 50-V range
p17 Span calibration value for 50-V range
p18 Zero calibration value for Pt:1 mA
p19 Span calibration value for Pt:1 mA
p20 Zero calibration value for Pt:2 mA
p21 Span calibration value for Pt:2 mA
p22 Span calibration value for Pt:1 mA-H
p23 Span calibration value for Pt:2 mA-H
p24 Zero calibration value for Cu:2 mA
p25 Span calibration value for Cu:2 mA
Correcting the calibration value manually (DCV/TC/
DI input module)
Setting XZp1, p2, ..... , p17<terminator>
p1 Unit number (0 to 5)
p2 Slot number (0 to 5)
p3 DISPLAY
p4 Zero calibration value for 20-mV range
p5 Span calibration value for 20-mV range
p6 Zero calibration value for 60-mV range
p7 Span calibration value for 60-mV range
p8 Zero calibration value for 200-mV range
p9 Span calibration value for 200-mV range
p10 Zero calibration value for 2-V range
p11 Span calibration value for 2-V range
p12 Zero calibration value for 6-V range
p13 Span calibration value for 6-V range
p14 Zero calibration value for 20-V range
p15 Span calibration value for 20-V range
p16 Zero calibration value for 50-V range
p17 Span calibration value for 50-V range
Correcting the calibration value manually (mA
input module)
Setting XZp1, p2, p3, p4, p5<terminator>
p1 Unit number (0 to 5)
p2 Slot number (0 to 5)
p3 DISPLAY
p4 Zero calibration value for 20-mA range
p5 Span calibration value for 20-mA range
Correcting the calibration value manually (Strain
input module)
Setting XZp1, p2, p3, ....., p9<terminator>
p1 Unit number (0 to 5)
p2 Slot number (0 to 5)
p3 DISPLAY
p4 Zero calibration value for 2k range
p5 Span calibration value for 2k range
p6 Zero calibration value for 20k range
p7 Span calibration value for 20k range
p8 Zero calibration value for 200k range
p9 Span calibration value for 200k range
Correcting the calibration value manually (Digital
input module)
Setting XZp1, p2, ..... , p7<terminator>
p1 Unit number (0 to 5)
p2 Slot number (0 to 5)
p3 DISPLAY
p4 Zero calibration value for 60-mV range
p5 Span calibration value for 60-mV range
p6 Zero calibration value for 6-V range
p7 Span calibration value for 6-V range
Example Modify the span calibration value for the 6V range of
the module in slot 1 of subunit 0 to 32000.
XZ0, 1, DISPLAY, , , , 32000
Storage of A/D calibration data in a module (A/D
calibration END processing)
Setting XZp1, p2, p3, p4<terminator>
p1 Unit number (0 to 5)
p2 Slot number (0 to 5)
p3 END
p4 Storage selection (ABORT, STORE)
Example Store the calibrated values for the module in slot 1 of
subunit 0.
XZ0, 1, END, STORE
Comments • You must execute STORE using A/D calibration
end processing each time after making an A/D
calibration or adjustment for one module. If A/D
calibration end processing (STORE) is not
executed, the calibrated data will not take effect.
• Since it takes an indefinite time to execute the XZ
command, return an ACK after the processing
ends.
• On the controller side, execute the following
processing after receiving an ACK after
transmitting the XZ command. The format of the
ACK status is as follows:
E0Cr+Lf The received command was normally
processed.
E1Cr+Lf There is an error in the received
command.
• If A/D calibration data are adjusted, inputting a
numeric value which is out of the setting range
disables the modules to be recognized. For
details, see the separate manual (IM DR231-01E
or IM DR232-01E).
6.5 Other Settings
- Communication Interface 1
- Instruction Manual 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 6
- CHAPTER 8 SAMPLE PROGRAM 6
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- Configuring from the PC 36
- 4.5 Connection Methods 37
- DR's IP address 42
- <Enter> 42
- 4.9 Setting the T imeout 43
- 5.1 Command Format 44
- 5.2 Command Syntax 46
- ●Stand alone model (DR130) 47
- 5.4 Command List 48
- Control Execution Command 49
- Output Request Command 49
- 5.4 Command List 49
- 5.5 Input Range Parameter 50
- RATE RATE 0 to 30000 52
- GATE GATE 0 to 30000 52
- 5.6 ASCII Code Table 54
- 6.1 Setting the Input 55
- Setting Scaling 56
- 6.1 Setting the Input 56
- SN Sets the scaling unit 57
- XQ Sets the filter 57
- 6.2 Setting Alarms 58
- 6.3 Setting the Display 59
- 6.4 Setting the Recording 60
- Commands 61
- Message setting 61
- Message copy 61
- XC Sets dot printing colors 63
- 6.5 Other Settings 64
- XB Sets the burnout 68
- 6.6 Control and Execution 71
- RS Reconstruct the system 74
- RC Initialize the set values 74
- 6.7 Data Output Request 75
- 7.1 Functions as Talker 77
- (ASCII code) 78
- (Binary code) 79
- Position 83
- ±DDDDDE-EpCrLf 87
- For Measured Data 90
- For Computed Data 90
- 7.13 Report Output Format 92
- Daily Report 94
- 7.13 Report Output Format 94
- Monthly Report 96
- 8.1 GP-IB Sample Programs 99
- IM DR231-11E 100
- 8.2 RS-232-C Sample Programs 102
- Output the Setting Data 105
- Sample Program 107
- 8.4 Ethernet Program 111
- 8.4 Ethernet Program 112
- App.1 Computing Equation 113
- Computation start 115
- Computation stop 115
- Computation clear & start 115
- Computed data 116
- Command Index 120
Manuais e produtos relacionados com Sensores Yokogawa DR240
Sensores Yokogawa µR20000 Manual do Utilizador
(263 páginas)
(263 páginas)
Sensores Yokogawa DR240 Manual do Utilizador
(293 páginas)
(293 páginas)
Sensores Yokogawa JUXTA VJCE Manual do Utilizador
(10 páginas)
(10 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais